Signal Tutorial (Part 1)

[seoul_style]

Thanks for uploading these tutorials. The community is very dedicated and helpful here. I am planning to build a small route and these videos will come in handy!

[gurugordon]

Thanks Mark. Appreciated.

Gordon

[Bananarama]

Try these - they were posted over at RWA:

Signal Tutorial Part 1:https://www.youtube.com/watch?v=qYUkfQqQcY8
Signal Tutorial Part 2:https://www.youtube.com/watch?v=s1_LkSx_MGM
Signal Tutorial Part 3:https://www.youtube.com/watch?v=0Zu_Mjx9c2E
Signal Tutorial Part 4:https://www.youtube.com/watch?v=jn2s3HdMkY4
Signal Tutorial Part 5:https://www.youtube.com/watch?v=DAcUsioSNkE
Signal Tutorial Part 6:https://www.youtube.com/watch?v=bx9W4bEwZa4

Signal Follow-up Link Placement:https://www.youtube.com/watch?v=bKDk-v8PdAQ

Signal Tutorial for Blocking Part 1:https://www.youtube.com/watch?v=0nXVa5FroZY
Signal Tutorial for Blocking Part 2:https://www.youtube.com/watch?v=US4KSFh4vBY
Signal Tutorial for Blocking Part 3:https://www.youtube.com/watch?v=zj0wxfHex4U
Signal Tutorial for Blocking Part 4:https://www.youtube.com/watch?v=GoCJs8jHJzo
Signal Tutorial for Blocking Part 5:https://www.youtube.com/watch?v=rYdXNrjCaR8

[gurugordon]

What happened to the tutorial? I'm seeing a blank page where it should be.

[trainrcool]

thanks pikehkr for the videos for signals. what i did was made the same route and place the same kinda signals well i use the default ones that came with game and it work just like in the video. just to get understanding on how it works but ya i got to say placeing signals is really easy in railworks. now i'm ready to place signals on my others routes. thanks so so much.

[OrpheusRocker]

Pikehkr,

Thank you very much for the tutorial. I've been locked in mortal combat with a signal test route for months and your tutorial might just help me make sense of it all.

I'd set aside some time tomorrow to have a go with my latest DLC acquisitions but I'm going to play with the signalling again.

Fair play to you for taking the time to gain this knowledge and spending the time to pass it on.

Andy

[pikehkr]

Hiya,

I just want to add here that this is not a rule book. This is just how I do signaling and get consistent results.

If you are signaling in tight quarters, like a yard ladder then the basic rules of (keep your links in separate ribbons and don't place them across the ribbon outlines) do not apply.

For general signaling though, these are good guidelines that will keep you out of trouble.

Keep an eye open for more tutorials covering yard ladders and other unusual situations.

Pikehkr

[tomkat41]

Hi Pike,

I move your thread to the RW Tutorials And Links Forum and made it a sticky. It's a good tutorial and taught me something about it.

[pikehkr]

I found that if I did not do that, sometimes the signals would not initialize properly or would not recognize when you switched the junction. Usually this was when signaling junctions that were close together, such as a yard ladder or like in my tutorial, where I have a few junctions close to each other.

At first, I tried placing the link inside the frog of each line but that did not give consistent results. Sometimes the signal would change, sometimes not, even though the links were positioned the same for each junction.

After many hours of placing signals I found that most often if I was having trouble, I would find that multiple signal links were in the same long ribbon section of track. I also found if I split and welded the offending section the signal would start working correctly. I just incorporated it into my routine when signaling and it helps with link placement.

To be honest I think the issue is more of a track ribbon data issue in the data files than a signaling issue but it manifests itself in the signals not working correctly. The split/weld routine seems to fix the track ribbon data issue, if it exists, for the junction.

I'll see if I can come up with a sample and make a video to show you what I am talking about but like I said, it is rare due to the fact that is a combination affect. The ribbon data must be a little off and you must be signaling that same area otherwise you would never know the problem existed. My way just seems to stop this error from appearing randomly as I do the preventative split/weld on all junctions.

Pikehkr

[eyein91681]

ADMINS PLS STICKY THIS TUTORIAL

thanks

[AdamL]

Hiya,

Can you explain why you are cutting track around junctions?

Cheers

[sleepyto]

WOW what a super set of tutorials. Answered a couple of questions for me.
A must see for anyone wanting to signal their routes.

Thanks again

[pikehkr]

Links to parts 3 - 6 are at pikesproducts.com, in the forum.

Pikehkr