Tab Content
  • longiron's Avatar
    11-21-2017, 10:49 PM
    longiron replied to a thread B&O West End in MSTS Route Design
    Construction crews managed to lay track to the summit of the Alleghenies, between Altamont and Wilson. Built AM tower controlling the area. Still...
    24 replies | 1287 view(s)
  • longiron's Avatar
    11-21-2017, 10:46 PM
    longiron replied to a thread B&O West End in MSTS Route Design
    thanks
    24 replies | 1287 view(s)
  • longiron's Avatar
    11-18-2017, 09:44 AM
    Thanks, but this looks a little scary for me. With TSRE now available, I'll just use the tool. Thanks anyway
    5 replies | 292 view(s)
  • longiron's Avatar
    11-17-2017, 06:47 PM
    longiron replied to a thread what ever became of Michelle? in BVE
    Found this forum post: https://forums.bvestation.com/index.php?topic=1644.0
    2 replies | 192 view(s)
  • longiron's Avatar
    11-16-2017, 11:08 PM
    Never knew about the RE "T" trick. Thanks so much.
    5 replies | 292 view(s)
  • longiron's Avatar
    11-16-2017, 08:40 PM
    Is laying a 12% grade possible in MSTS? The RE grade tool only goes to 3.00 which is 5.25%. So does anyone know if TSRE can lay a 12% grade. Needed...
    5 replies | 292 view(s)
  • longiron's Avatar
    11-16-2017, 08:36 PM
    longiron replied to a thread B&O West End in MSTS Route Design
    Enough to make activities for Westport/Piedmont area, since there was an interchange across from the paper mill. And IF I get to Cumberland, then a...
    24 replies | 1287 view(s)
  • longiron's Avatar
    11-16-2017, 08:04 PM
    longiron replied to a thread B&O West End in MSTS Route Design
    Dave, Really appreciate the offer. And I'd love to take you up on it. I'm probably 3 months away from getting there. Lot's of 17 mile grade to lay...
    24 replies | 1287 view(s)
  • longiron's Avatar
    11-16-2017, 08:00 PM
    longiron replied to a thread B&O West End in MSTS Route Design
    Yes, unfortunately there's not a lot, visually, going on for 11 miles up or down Cranberry Grade from Rowlesburg to Terra Alta, with the exceptions...
    24 replies | 1287 view(s)
  • longiron's Avatar
    11-15-2017, 03:56 PM
    longiron replied to a thread B&O West End in MSTS Route Design
    Yessir. I'm going to spend some polys & time on a realistic model of this iconic structure. Contacted the architecture firm that did the remodel...
    24 replies | 1287 view(s)
  • longiron's Avatar
    11-15-2017, 10:58 AM
    longiron replied to a thread B&O West End in MSTS Route Design
    Lots of work left to do on the landmark Baldwin-designed station.
    24 replies | 1287 view(s)
  • longiron's Avatar
    11-13-2017, 09:43 PM
    longiron replied to a thread B&O West End in MSTS Route Design
    Work continues west of Deer Park towards Altamont, so a few scenes leaving the area. Looking back at the Mountain Lake Park helper area Nice...
    24 replies | 1287 view(s)
  • longiron's Avatar
    10-29-2017, 08:29 AM
    longiron replied to a thread B&O West End in MSTS Route Design
    I'm working off a 1936 track chart. Buildings are representative of 1946/47. Things really didn't start to change until mid-1950s when dieselization...
    24 replies | 1287 view(s)
  • longiron's Avatar
    10-28-2017, 11:32 PM
    longiron replied to a thread B&O West End in MSTS Route Design
    Mountain Lake Park helper station where two B&O Q-4b's were stationed to assist coal & merchandise trains eastward to Altamont
    24 replies | 1287 view(s)
  • longiron's Avatar
    10-28-2017, 11:26 PM
    Station stop: Deer Park, MD. Home of the famous Deer Park Spring water served on all the B&O passenger trains. The Deer Park station was demolished...
    24 replies | 1287 view(s)
No More Results

4 Visitor Messages

  1. View Conversation
    5300, 5308 works just fine
  2. Never had anyone report crashing with either models (each having over 1,000 downloads). Which one? 5300 or 5308? They both share the same 3D mesh, just different texture maps
    chris
  3. View Conversation
    I found this really odd bug with the B&O P7 where when I try to run it in MSTS, it crashes my game, but it works fine in ORTS, do you know anything about that?
  4. View Conversation
    Chris,
    Send me any details you have for the loco (I haven't yet had a chance to see if I have any info on this series in my library) + your .eng file, assuming this is MSTS and not RS. If it is RS, I'll need the Engine file and the entire Simulation folder. If you want to try yourself, I have made the spreadsheet I use to calculate the setup values available in the library. Search on my name in the libraries.
    You can use [email protected] for direct email contact.
    Bill
    I am posting this way because I am not familiar with using this feature.
Showing Visitor Messages 1 to 4 of 4
About longiron

Basic Information

About longiron
Full Name:
Chris Vanwagoner
Location:
Just south of NYC
Occupation:
Enterprise software

Signature


Chris
"True rail fans have two favorite railroads. The B&O and one other."

Statistics


Total Posts
Total Posts
1,244
Posts Per Day
0.31
Visitor Messages
Total Messages
4
Most Recent Message
03-05-2017 09:51 PM
General Information
Last Activity
Today 12:11 AM
Join Date
01-15-2007
Referrals
0

2 Friends

  1. jpetersjr  jpetersjr is offline

    Senior Member

    • Send a message via Yahoo to jpetersjr
    jpetersjr
  2. Moore  Moore is offline

    Junior Member

    Moore
Showing Friends 1 to 2 of 2