Search:

Type: Posts; User: rockislandfan

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    911

    Most Route sounds for MSTS and Open Rails use a...

    Most Route sounds for MSTS and Open Rails use a resample rate of 11025KHz. If you are messing with engine sounds then they can also be 2205KHz or even 44100KHz. Load the original file that you are...
  2. Replies
    9
    Views
    911

    For starters, when you create new wave files be...

    For starters, when you create new wave files be sure to save them as 16bit. Also be sure to match the frequency of the wave file as to what is in the SMS file.

    Ron
  3. Replies
    17
    Views
    2,493

    Excellent looking models! Thanks for all your...

    Excellent looking models! Thanks for all your hard work.

    Ron
  4. Replies
    3
    Views
    709

    It looks like you could make an E8 or E9 out of...

    It looks like you could make an E8 or E9 out of that.

    Ron
  5. Those are some great looking SD40 loco's!!! Ron

    Those are some great looking SD40 loco's!!!

    Ron
  6. Why not work with the texture files and just...

    Why not work with the texture files and just alpha one of the switch stands out so it doesn't show anywhere in the route?

    Ron
  7. Replies
    27
    Views
    5,632

    You can also click on them and drag them. Just...

    You can also click on them and drag them. Just move them a little bit away from the tracks.
  8. I just looked at a lot of photos. They do seem to...

    I just looked at a lot of photos. They do seem to only be the on the front truck except if it is an end cab switcher such as a SW1200. Then it is on the rear truck only. I don't think it is just for...
  9. If you reduce the slug's power to zero you won't...

    If you reduce the slug's power to zero you won't be able to take advantage of the slugs tractive effort. You will be towing a dead unit around. The closest thing to do to mimic the real thing is what...
  10. Replies
    43
    Views
    7,465

    Another vote for fallen flags and older stuff. ...

    Another vote for fallen flags and older stuff.

    Ron
  11. Replies
    6
    Views
    1,351

    You will only get in trouble if you put flat...

    You will only get in trouble if you put flat spots on the engine. At least that's the way it used to be.

    Ron
  12. Replies
    10
    Views
    2,191

    The GE "U" series throttle still had 8 notches....

    The GE "U" series throttle still had 8 notches. What it did have was half notches between each numbered notch. So if it was MU'd with say an EMD then the half notches were just ignored. Some...
  13. Replies
    13
    Views
    2,848

    The strange thing is that it's an Open Rails...

    The strange thing is that it's an Open Rails thing. If you run them in MSTS the trucks work fine.

    Ron
  14. Replies
    73
    Views
    13,039

    Thanks for uploading these, they are appreciated....

    Thanks for uploading these, they are appreciated.

    Ron
  15. Replies
    73
    Views
    13,039

    How about some dead tree branches, they wouldn't...

    How about some dead tree branches, they wouldn't need to have any leaves on them. Some broken off tree stumps would be nice too.
    Just a thought.

    Ron
  16. Replies
    73
    Views
    13,039

    Garbage never looked so good! Ron

    Garbage never looked so good!

    Ron
  17. Replies
    4
    Views
    934

    How about a sidewalk along the front. Even if it...

    How about a sidewalk along the front. Even if it is facing away from the tracks there will still be times it could be seen from the front while using an outside camera view.
    Just a thought.
  18. Replies
    14
    Views
    1,993

    If you run explore mode in OR and you have...

    If you run explore mode in OR and you have disabled the TCS scripts and speed control but still find yourself going into emergency while passing some signals, then try this. Open the engine file of...
  19. Replies
    2
    Views
    902

    Daniel, check to make sure that your inside cab...

    Daniel, check to make sure that your inside cab sounds are stereo and that your outside sounds are mono.

    Ron
  20. Replies
    197
    Views
    40,536

    It's a tough one to figure out but the kicker is...

    It's a tough one to figure out but the kicker is that MSTS displays all the GP11's correctly.

    Ron
  21. Replies
    39
    Views
    6,740

    The BNSF story goes that in the early years right...

    The BNSF story goes that in the early years right after the merger BNSF was going to use both paint schemes at the same time. Then eventually the settled on using just the one ( orange and green)...
  22. Replies
    6
    Views
    1,293

    Take a look at this file "ctc_swbx.zip", it may...

    Take a look at this file "ctc_swbx.zip", it may be what you want.


    Ron
  23. Replies
    2
    Views
    968

    I am still here but I have been very bust lately....

    I am still here but I have been very bust lately.

    Ron
  24. Replies
    4
    Views
    2,863

    That is my GP38 sound set, however there are four...

    That is my GP38 sound set, however there are four extra horn files included which are not mine. All my wave files have the "RF" prefix. I have no clue who did the other horns. They were probably...
  25. Replies
    197
    Views
    40,536

    That is an awesome piece of work. It looks spot...

    That is an awesome piece of work. It looks spot on.

    Ron
Results 1 to 25 of 329
Page 1 of 14 1 2 3 4